AtlasIED Login
Password
IP Power Strip Interface


StatusAlarmSchedulerNetwork SettingsConfiguration

Grouped Outlets Sequence ON/OFF 

Temperature

Humidity

Voltage

Current

Status - Important: Refresh the Web browser page for real time status.
Panel Outlet On/Off SwitchesEnabled
Device Type
Unit Name
Watts
Temperature Alarm
Humidity Alarm
Current Alarm
Voltage Alarm
Incoming AC Mains Protection, Surge & Ground

NOTE: When Green, protection is OK. When Red service is required.

Firmware Version

Outlet Status & Manual On/Off SwitchesON / OFF
Circuit-1
Circuit-2
Circuit-3
Circuit-4
Circuit-5
Circuit-6
Circuit-7
Circuit-8

NOTE: Individual outlets can be turned ON / OFF by selecting them. When the Power is reset, the group programming will apply if enabled.



Alarm

Temp AlarmEnable
Temperature ()
Humidity Alarm (15 - 95%)Enable
Humidity (%)
Current AlarmEnable
Current (A) Average Current
Voltage Alarm
Over Voltage (100 - 140V)
Under Voltage (80 - 120V)
Voltage Alarm RecoveryAuto RecoverManual Reset

NOTE: When the voltage alarm is enabled and the over or under voltage settings is reached, the AC Outlets will shut OFF. If Auto Recover is selected, the unit will turn back ON when the voltage is stabilized. If Manual Reset is selected, the power switch will need to be manually reset once the voltage is stablized.


Alarm Activation Log
Logs will be printed here......


Scheduler

Day/Time NTP
Time Zone
Daylight SavingsEnable
NTP ServerEnable
Group Outlets Schedule (Sequenced)
Enter 24Hr Clock Settings
Enable
Weekday
MTWTHFSASU
Individual Outlet Scheduled Time
Enable
Weekday
MTWTHFSASU
Outlet 1
Outlet 2
Outlet 3
Outlet 4
Outlet 5
Outlet 6
Outlet 7
Outlet 8

NOTE 1: If the fan control is enabled, outlet 8 cannot be assigned to the group setting.

NOTE 2: If an outlet is assigned to a group setting, individual outlet schedule cannot be used.



Network Settings

Network Interface
Host IP SettingStaticDHCP
Static IP
Mask
Gateway

Auto Ping Reset
Circuit-1
Circuit-2
Circuit-3
Circuit-4
Circuit-5
Circuit-6
Circuit-7
Circuit-8
Auto Ping Intervals (10 - 60 min.)

Note: For the Auto Ping to function correctly, the devices plugged into outlets 1-8 need to be on the same LAN and Subnet as the IP Power Strip. An Auto Ping will be sent to each device that is enable to receive a diagnostic ping. The Auto Ping interval is set in minutes. If the device being pinged does not respond, the outlet that the device is plugged into will be cycled. The next Auto Ping test will occur on the next assigned time interval that was set in the minutes setting.


Password
Login Password
Reboot

NOTE: Reboot does not affect the AC outlets.

Factory Default


Configuration

Function
Panel Outlet On/Off SwitchesEnable
AC Fan Control Setting (Outlet 8)
Enable
NOTE: When enabled Outlet 8 cannot be assigned to a group or schedule.
Fan On Temp
Fan Off Temp
Sequence Delay Time (sec)
External Meter AP-LEDIP Display View
Temperature Reading F / C

Group Management
Group Assignment
Outlet 1Assign
Outlet 2Assign
Outlet 3Assign
Outlet 4Assign
Outlet 5Assign
Outlet 6Assign
Outlet 7Assign
Outlet 8Assign

NOTE: If the fan control is enabled, outlet 8 cannot be assigned to the group setting.

NOTE: If an outlet is assigned to a group setting, individual outlet schedule will be removed.


Unit & Outlet Name Assignment
Unit Name
Outlet Name 1
Outlet Name 2
Outlet Name 3
Outlet Name 4
Outlet Name 5
Outlet Name 6
Outlet Name 7
Outlet Name 8

NOTE: Either unit name or outlet name is limited to 16 characters (A~Z, 0~9, no special characters).